Description
Associated 6066A Intellamatic Smart Parallel Charger, 12V, 30/60A, 1-20 Batteries, 110VAC
Model 6066A battery charger is designed to charge one to ten 12 Volt batteries in parallel. The multiple charge rates allow batteries to be slow charged or fast charged at a rate not to exceed the 30 amp output of the charger. The voltmeter allows you to adjust the charge rate to compensate for battery type (see charging instructions).
This unit is not intended to be used as a car starting unit. The output leads are terminated in ring terminals and designed to be permanently attached to a parallel bus bar or charging rack.
– Charges 1-20 12 Volt batteries in parallel in less than 24 hours
– Automatic with 3 settings: Flooded, AGM, Manual
– Three LED indicators showing charging status
– Two output settings: 60A and 30A
– Analog voltage and current meters
– Can be mounted on a wall or bench
– Made in USA of US and Global Components
– 1 Year Bumper-to-Bumper Warranty
Additional Accessories (Not Included)
– – Standard Bus Bar. Includes insulated fiberglass backboard, 10 pairs of charging leads with 300A insulated clamps.
– – Circuit Breaker Bus Bar. Includes insulated fiberglass backboard, 10 pairs of charging leads with 300A insulated clamps, and auto-reset circuit breaker protecting each positive lead.
– – SMART Bus Bar. Includes insulated fiberglass backboard, 10 pairs of charging leads with 300A insulated clamps and a microprocessor controller protecting and monitoring each charging circuit.
– – In-Vehicle Bus Bar. Includes insulated fiberglass backboard, 4 pairs of 20 ft long charging leads with 300A insulated clamps and circuit breaker protection and monitoring on each charging circuit.
– – Battery Charging Rack with 10 Charging Lead Sets.
Specifications
AC Input: 120V, 12A, 60Hz
DC Output: 60/30A, 14.9V
Charging Capacity: 1-20, 12V Battery
Battery Types: Conventional/Maintenance-Free Flooded Cell, AGM
Parallel/Series/Individual Design: Parallel
Smart Charger/Battery Diagnostics: Yes
Charge Rate Settings: 2
Volt Meter: 11-17V Analog
Amp Meter: 0-100A Analog
DC Cables: 6.5 ft, 6.5 AWG
DC Clamp: N/A (Lugs Only)
AC Cord: 6.5 ft, 16-3, North American 3-prong Plug
Shipping Wt: 40 lbs
Operation: LED Light Indications
(see Operator’s Manual for complete instructions)
– SLOW BLINKING RED: Indicates possible weak battery.
– FAST BLINKING RED: Before charge this indicates first battery is connected backwards, check connection.
– CONTINUOUS RED: Indicates AC power is on.
– CONTINUOUS GREEN: Indicates correct connection. After battery is connected, if the green light does not light, check for proper polarity or poor connections. If the battery voltage is below 4 volts the green light will not come on.
– BLINKING GREEN: Indicates charge is complete, charger in the float mode.
– CONTINUOUS YELLOW: Indicates charging, bulk charge, less than 80% charged.
– BLINKING YELLOW: Indicates finish charge, greater than 80% charged.
– FLASHING GREEN AND YELLOW: Indicates deep discharge recovery process.
NOTES
FOUR SECOND DELAY
To avoid sparking, the charger tests for correct polarity before applying current to the battery. When connected properly, the green light will come on for 4 seconds before the yellow light comes on.
DEEP DISCHARGE RECOVERY
If the charger determines a battery is deeply discharged, it will attempt to recover the battery with a program designed to enhance charge acceptance. Because of the high voltage levels required for recovery, this program is not included for sealed batteries. If charger does not recover battery then charger will shut off.
Information Downloads
Check the match before ordering
- Part numberMatch the complete number, including letters and suffixes.
- Electrical specificationConfirm voltage, chemistry and charging requirements.
- Physical fitCompare dimensions, connector, polarity and terminal position.
